广东联通和广东电信宽带互通已被限速

2 天前
 wayne630

广东联通到广东电信上传限速已经是进入作死阶段了,黑猫有投诉,但案例暂时不是很多。

用签约上行速率为 150Mbps 的联通商务极光测试如下( IPv4 和 IPv6 均为动态公网,此宽带从未跑过 PCDN ,上传与下载流量的比值大约为 0.8:1 ,用联通自助测速平台测试均能测到满速,以下结果均为大约数值): IPv4 上传到电信家宽:10Mbps ; IPv6 上传到电信家宽:1Mbps ; IPv4 上传到电信 4G/5G:2Mbps ; IPv6 上传到电信 4G/5G:1Mbps ; 上午 10 时-晚上 7 时与电信家宽互 ping:35ms ; 晚上 7 时后-0 时与电信家宽互 ping:50-60ms ;

但是用电信家宽 ping 一些联通数据中心的 IP 段延时是个位数的,电信上传给联通也能跑满上行签约速率。广东联通是把用户的所有上传行为都判定为 PCDN 了吗?

4662 次点击
所在节点    宽带症候群
84 条回复
amyw495062
1 天前
@wwc625 给你石锤了,艾欧尼亚确实不是 bgp ,我这里也受影响了,现在晚上 9 点,延迟 40
amyw495062
1 天前
@wwc625 不对,进游戏就 60 了,我吐了
bclerdx
1 天前
@wayne630 你难道这还不知道什么意思啊?很明显啊。
wwc625
1 天前
@amyw495062 擦,这狗比运营商,不知道是长期的还是暂时的啊
amyw495062
1 天前
@wwc625 不知道,狗币来的,我在 WeGame 看是 40 多,一进游戏真实延迟 60 多,之前我也是个位数到 10 几出头的,现在恶心了,60~70 来回跳,还不稳定
656711352
1 天前
@yyzh 广移只是针对跨省,对实际用户体验来说有限
TWSF
1 天前
广东电信 ping 广东联通
正在 Ping 221.4.66.66 具有 32 字节的数据:
来自 221.4.66.66 的回复: 字节=32 时间=60ms TTL=242
来自 221.4.66.66 的回复: 字节=32 时间=55ms TTL=242
来自 221.4.66.66 的回复: 字节=32 时间=60ms TTL=242
来自 221.4.66.66 的回复: 字节=32 时间=54ms TTL=242

广东电信 ping 北京联通
正在 Ping 61.49.140.205 具有 32 字节的数据:
来自 61.49.140.205 的回复: 字节=32 时间=93ms TTL=244
来自 61.49.140.205 的回复: 字节=32 时间=93ms TTL=244
来自 61.49.140.205 的回复: 字节=32 时间=87ms TTL=244
来自 61.49.140.205 的回复: 字节=32 时间=92ms TTL=244
foru17
1 天前
联通和电信都是 1000M 下行 / 50M 上行的宽度。两边通过 tailsclae 打洞,公网 IPv6 direct 直连。

我用深圳联通给我电信做出境中转,大多时候都能跑满宽度,但是偶发联通上行比较低。但是刚刚测试了下,发现应该还是正常。


深圳联通 ping 东莞电信 via IPv6
PING 240e:3b1:d0b0:****:613f:ef:6710:**dg (240e:3b1:d0b0:a000:613f:ef:6710:**dg): 56 data bytes
64 bytes from 240e:3b1:d0b0:****:613f:ef:6710:**dg: seq=0 ttl=54 time=34.604 ms
64 bytes from 240e:3b1:d0b0:****:613f:ef:6710:**dg: seq=1 ttl=54 time=34.080 ms
64 bytes from 240e:3b1:d0b0:****:613f:ef:6710:**dg: seq=2 ttl=54 time=37.671 ms
64 bytes from 240e:3b1:d0b0:****:613f:ef:6710:**dg: seq=3 ttl=54 time=37.064 ms
64 bytes from 240e:3b1:d0b0:****:613f:ef:6710:**dg: seq=4 ttl=54 time=32.824 ms
64 bytes from 240e:3b1:d0b0:****:613f:ef:6710:**dg: seq=5 ttl=54 time=36.763 ms


东莞电信 ping 深圳联通 via IPv6
❯ ping6 2408:8256:3083:cba8:****:c4ff:fe44:**sz
PING6(56=40+8+8 bytes) 240e:3b1:d0b0:a000:613f:ef:6710:**dg --> 2408:8256:3083:cba8:****:c4ff:fe44:**sz
16 bytes from 2408:8256:3083:cba8:****:c4ff:fe44:**sz, icmp_seq=0 hlim=54 time=36.836 ms
16 bytes from 2408:8256:3083:cba8:****:c4ff:fe44:**sz, icmp_seq=1 hlim=54 time=33.406 ms
16 bytes from 2408:8256:3083:cba8:****:c4ff:fe44:**sz, icmp_seq=2 hlim=54 time=38.218 ms
16 bytes from 2408:8256:3083:cba8:****:c4ff:fe44:**sz, icmp_seq=3 hlim=54 time=38.890 ms
16 bytes from 2408:8256:3083:cba8:****:c4ff:fe44:**sz, icmp_seq=4 hlim=54 time=35.091 ms


[iperf3 测速:东莞电信 Client > 深圳联通 Server]
❯ iperf3 -c 192.168.101.50 -t 60
Connecting to host 192.168.101.50, port 5201
[ 4] local 100.121.54.15 port 61423 connected to 192.168.101.50 port 5201
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-1.00 sec 12.6 MBytes 105 Mbits/sec
[ 4] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec
[ 4] 2.00-3.00 sec 633 KBytes 5.20 Mbits/sec
[ 4] 3.00-4.00 sec 1.94 MBytes 16.3 Mbits/sec
[ 4] 4.00-5.00 sec 2.98 MBytes 25.0 Mbits/sec
[ 4] 5.00-6.00 sec 3.84 MBytes 32.3 Mbits/sec
[ 4] 6.00-7.00 sec 4.85 MBytes 40.7 Mbits/sec
[ 4] 7.00-8.00 sec 5.51 MBytes 46.2 Mbits/sec
[ 4] 8.00-9.00 sec 6.28 MBytes 52.7 Mbits/sec
[ 4] 9.00-10.00 sec 7.11 MBytes 59.7 Mbits/sec
[ 4] 10.00-11.00 sec 9.32 MBytes 78.2 Mbits/sec
[ 4] 11.00-12.00 sec 5.05 MBytes 42.4 Mbits/sec
[ 4] 12.00-13.00 sec 669 KBytes 5.47 Mbits/sec
[ 4] 13.00-14.00 sec 1.66 MBytes 13.9 Mbits/sec
[ 4] 14.00-15.00 sec 2.66 MBytes 22.3 Mbits/sec
[ 4] 15.00-16.00 sec 3.51 MBytes 29.4 Mbits/sec
[ 4] 16.00-17.00 sec 4.46 MBytes 37.4 Mbits/sec
[ 4] 17.00-18.00 sec 5.34 MBytes 44.8 Mbits/sec
[ 4] 18.00-19.00 sec 5.95 MBytes 49.9 Mbits/sec
[ 4] 19.00-20.00 sec 7.13 MBytes 59.8 Mbits/sec
[ 4] 20.00-21.00 sec 8.48 MBytes 71.1 Mbits/sec
[ 4] 21.00-22.00 sec 7.62 MBytes 63.9 Mbits/sec
^C[ 4] 22.00-22.53 sec 237 KBytes 3.70 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-22.53 sec 108 MBytes 40.1 Mbits/sec sender
[ 4] 0.00-22.53 sec 0.00 Bytes 0.00 bits/sec receiver

[iperf3 翻转测试:东莞电信 Client > 深圳联通 Server]
❯ iperf3 -c 192.168.101.50 -t 60 -R
Connecting to host 192.168.101.50, port 5201
Reverse mode, remote host 192.168.101.50 is sending
[ 4] local 100.121.54.15 port 61000 connected to 192.168.101.50 port 5201
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-1.00 sec 10.6 MBytes 88.8 Mbits/sec
[ 4] 1.00-2.00 sec 12.3 MBytes 103 Mbits/sec
[ 4] 2.00-3.00 sec 5.08 MBytes 42.5 Mbits/sec
[ 4] 3.00-4.00 sec 3.51 MBytes 29.5 Mbits/sec
[ 4] 4.00-5.00 sec 2.14 MBytes 18.0 Mbits/sec
[ 4] 5.00-6.00 sec 1.95 MBytes 16.4 Mbits/sec
[ 4] 6.00-7.00 sec 1.73 MBytes 14.5 Mbits/sec
[ 4] 7.00-8.00 sec 1.97 MBytes 16.5 Mbits/sec
[ 4] 8.00-9.00 sec 1.98 MBytes 16.6 Mbits/sec
[ 4] 9.00-10.00 sec 1.62 MBytes 13.6 Mbits/sec
[ 4] 10.00-11.00 sec 1.13 MBytes 9.45 Mbits/sec
[ 4] 11.00-12.00 sec 1.36 MBytes 11.5 Mbits/sec
[ 4] 12.00-13.00 sec 1.86 MBytes 15.6 Mbits/sec
[ 4] 13.00-14.00 sec 2.23 MBytes 18.7 Mbits/sec
[ 4] 14.00-15.00 sec 2.27 MBytes 19.0 Mbits/sec
[ 4] 15.00-16.00 sec 1.63 MBytes 13.7 Mbits/sec
[ 4] 16.00-17.00 sec 2.10 MBytes 17.6 Mbits/sec
[ 4] 17.00-18.00 sec 2.46 MBytes 20.6 Mbits/sec
[ 4] 18.00-19.00 sec 2.97 MBytes 24.9 Mbits/sec
[ 4] 19.00-20.00 sec 3.35 MBytes 28.1 Mbits/sec
[ 4] 20.00-21.00 sec 3.28 MBytes 27.6 Mbits/sec
^C[ 4] 21.00-21.96 sec 2.58 MBytes 22.5 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-21.96 sec 0.00 Bytes 0.00 bits/sec sender
[ 4] 0.00-21.96 sec 70.1 MBytes 26.8 Mbits/sec receiver



[iperf3 测速: 深圳联通 Client > 东莞电信 Server]

~# iperf3 -c 100.121.54.15 -t 60
Connecting to host 100.121.54.15, port 5201
[ 5] local 100.98.131.29 port 56150 connected to 100.121.54.15 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 4.66 MBytes 39.1 Mbits/sec 2 167 KBytes
[ 5] 1.00-2.00 sec 5.03 MBytes 42.2 Mbits/sec 0 194 KBytes
[ 5] 2.00-3.00 sec 5.59 MBytes 46.9 Mbits/sec 0 211 KBytes
[ 5] 3.00-4.00 sec 5.90 MBytes 49.5 Mbits/sec 0 218 KBytes
[ 5] 4.00-5.00 sec 6.21 MBytes 52.1 Mbits/sec 0 231 KBytes
[ 5] 5.00-6.01 sec 6.52 MBytes 54.3 Mbits/sec 0 248 KBytes
[ 5] 6.01-7.00 sec 6.52 MBytes 55.0 Mbits/sec 0 265 KBytes
[ 5] 7.00-8.00 sec 6.27 MBytes 52.6 Mbits/sec 6 207 KBytes
[ 5] 8.00-9.00 sec 6.39 MBytes 53.6 Mbits/sec 0 241 KBytes
[ 5] 9.00-10.00 sec 6.77 MBytes 56.8 Mbits/sec 0 260 KBytes
[ 5] 10.00-11.00 sec 6.46 MBytes 54.1 Mbits/sec 10 198 KBytes
[ 5] 11.00-12.00 sec 4.66 MBytes 39.1 Mbits/sec 1 155 KBytes
[ 5] 12.00-13.00 sec 4.84 MBytes 40.6 Mbits/sec 0 170 KBytes
[ 5] 13.00-14.00 sec 4.84 MBytes 40.6 Mbits/sec 0 188 KBytes
[ 5] 14.00-15.00 sec 4.10 MBytes 34.4 Mbits/sec 2 159 KBytes
[ 5] 15.00-16.00 sec 4.47 MBytes 37.5 Mbits/sec 0 176 KBytes
[ 5] 16.00-17.00 sec 5.21 MBytes 43.7 Mbits/sec 0 185 KBytes
[ 5] 17.00-18.00 sec 4.90 MBytes 41.1 Mbits/sec 3 144 KBytes
^C[ 5] 18.00-18.72 sec 2.98 MBytes 34.9 Mbits/sec 0 165 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-18.72 sec 102 MBytes 45.9 Mbits/sec 24 sender
[ 5] 0.00-18.72 sec 0.00 Bytes 0.00 bits/sec receiver

[ iperf3 翻转测试 深圳联通 Client > 东莞电信 Server ]

~# iperf3 -c 100.121.54.15 -t 60 -R
Connecting to host 100.121.54.15, port 5201
Reverse mode, remote host 100.121.54.15 is sending
[ 5] local 100.98.131.29 port 50394 connected to 100.121.54.15 port 5201
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 8.03 MBytes 67.4 Mbits/sec
[ 5] 1.00-2.00 sec 589 KBytes 4.82 Mbits/sec
[ 5] 2.00-3.00 sec 1.47 MBytes 12.3 Mbits/sec
[ 5] 3.00-4.00 sec 2.38 MBytes 20.0 Mbits/sec
[ 5] 4.00-5.00 sec 3.34 MBytes 28.0 Mbits/sec
[ 5] 5.00-6.00 sec 4.02 MBytes 33.7 Mbits/sec
[ 5] 6.00-7.00 sec 4.70 MBytes 39.4 Mbits/sec
[ 5] 7.00-8.00 sec 5.62 MBytes 47.1 Mbits/sec
[ 5] 8.00-9.00 sec 6.79 MBytes 57.0 Mbits/sec
[ 5] 9.00-10.00 sec 8.04 MBytes 67.4 Mbits/sec
[ 5] 10.00-11.00 sec 8.42 MBytes 70.6 Mbits/sec
[ 5] 11.00-12.00 sec 6.13 MBytes 51.4 Mbits/sec
[ 5] 12.00-13.00 sec 7.06 MBytes 59.2 Mbits/sec
[ 5] 13.00-14.00 sec 5.01 MBytes 42.0 Mbits/sec
[ 5] 14.00-15.00 sec 6.42 MBytes 53.8 Mbits/sec
[ 5] 15.00-16.00 sec 6.97 MBytes 58.5 Mbits/sec
[ 5] 16.00-17.00 sec 6.35 MBytes 53.3 Mbits/sec
[ 5] 17.00-18.00 sec 6.25 MBytes 52.4 Mbits/sec
[ 5] 18.00-19.00 sec 6.14 MBytes 51.5 Mbits/sec
^C[ 5] 19.00-19.63 sec 3.48 MBytes 46.3 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-19.63 sec 0.00 Bytes 0.00 bits/sec sender
[ 5] 0.00-19.63 sec 107 MBytes 45.8 Mbits/sec receiver
Kaiyuan
1 天前
额,还好我爸之前办的携号转联通送的一条联通宽带,现在我出国都走联通...然后电信有公网,手机连家里软路由转联通出国...现在我妹也是这样连我家。
S179276SP
1 天前
@QJES 0769 联通公网到你那差不多 20ms
wayne630
1 天前
@amyw495062 原来贴吧被骂那个是您!那里太多推联通宽带的,说联通不好会影响他们的业绩。所以来这讨论好了。
freedomNet
1 天前
终于有人说这个问题了!
写了一个脚本去检查 Ping time. 发现一个规律,就是从早上 10 点多到凌晨 12 点多,联通 Ping 电信的延迟是 30-60ms. 其他时间都是 9-12ms 左右。延迟高,当然也伴随速度下降。。
联通为什么突然那么恶心,维持这个状态已经至少有半个月时间。如果长期都是这样,以后还是不用联通了!
amyw495062
1 天前
@freedomNet 也不突然了,去年家宽没公网的很多都改 nat4 了,早烂完了,我就是一条商宽带公网,一条 58 低消没公网,我感觉有公网没公网都很烂。
milkman155
1 天前

广东联通到广东电信 联通出大问题
wayne630
1 天前
@Kaiyuan 现在是联通和电信互联的质量比国际还差得多,当然,如果您手机是联通,宽带也是联通就没有什么感觉的,但如果手机或其他有线网络环境是电信,利用联通中转出国的话,那么现在也一样卡得要死。
qwvy2g
1 天前
我这边还是北方十省市的联通,能明显感觉到高峰期联通内网访问都不是很顺畅,打开网页看视频有时都很费劲。平常也是偶尔卡一下的现象且永远也不会消失,登录光猫看了一下协议在 gpon 跑千兆宽带。
singing
1 天前
印象中 020 联通在 3 月开始就出现各种 qos
kenny9572
1 天前
丢,广东联通拉取广东移动的 http 数据,广移 50m 上传,联通直接限速 500k 。原来大家都是这个问题。
wayne630
1 天前
@singing 5 月份的时候我发现用这条联通宽带上传文件到天翼云盘就只有几十 K 一秒甚至断流,我当时还以为是天翼云盘问题,还投诉了电信,后来发现用电信上传啥事都没有,那个时候已经觉得联通是有问题的了,但认知仅限于“联通可能是为了让用户使用自家的沃云盘而限制用户使用竞争对手的云盘”。那个时候与我另外两个办公场所的电信宽带互通仍然是畅通无阻的,所以没在意。直到最近在用电信宽带的场所远程看装联通宽带场所的视频监控会卡顿,逐步排查才发现联通限速到这个丧心病狂的地步。
freedomNet
1 天前
@qwvy2g 联通内网都卡?那就更加离谱了!

这是一个专为移动设备优化的页面(即为了让你能够在 Google 搜索结果里秒开这个页面),如果你希望参与 V2EX 社区的讨论,你可以继续到 V2EX 上打开本讨论主题的完整版本。

https://www.v2ex.com/t/1073989

V2EX 是创意工作者们的社区,是一个分享自己正在做的有趣事物、交流想法,可以遇见新朋友甚至新机会的地方。

V2EX is a community of developers, designers and creative people.

© 2021 V2EX